Capability Overview

Powering tomorrow with
reliable electrical systems

Electrical failures trace back to the same root causes: improper design, inadequate installation, and no one checking the work before the wall gets closed. Our licensed electrical team approaches every project with one standard: design it right, install it right, document it completely, and test it before we leave.

  • Licensed electrical contractor for commercial & infrastructure work
  • Design, installation, documentation & testing under one team
  • Integrated with TBT civil, structural & architecture disciplines

"Design it right, install it right, document it completely, and test it before we leave."

The Black Table Standard
Key Benefits

What changes when one team owns the entire electrical scope

001

Code Compliance

All work designed and installed to current NEC and local amendment standards. We pull every permit required and pass every inspection the first time.

002

Integrated with EPC

When electrical is part of a larger TBT project, our team coordinates directly with civil and structural disciplines. No interface conflicts after the concrete is poured.

003

Full Documentation

Every installation documented with as-built drawings, panel schedules, equipment data sheets, and inspection records.

004

Energy Efficiency

Energy-efficient lighting, smart controls, and demand management solutions that reduce operating costs from day one.

005

Emergency Power

Generator, UPS, and ATS design and installation for facilities that require backup power, serving government, healthcare, and critical infrastructure clients.

006

EV & solar Ready

We size electrical systems with future EV charging and solar interconnection in mind, so you’re not paying to upgrade your service entry twice in five years.

Electrical Solutions

From wiring to full systems

Complete end-to-end electrical solutions designed to deliver strong, efficient, and resilient results for your site or community.

  • Electrical system design and engineering for commercial and industrial facilities

    Electrical Design

    Electrical Design

    Permit-ready electrical designs developed in coordination with architectural and structural teams, so conflicts are resolved on paper, not in the field.

    • Load calculations and demand analysis
    • Single-line diagrams and riser diagrams
    • Panel schedules and circuit directories
    • Conduit routing and raceway plans
    • Lighting design and fixture schedules
    • Short circuit and coordination studies
    • PE-stamped drawings where required

  • Service & Distribution
    Electrical service entry and power distribution panel installation

    Service & Distribution

    Service & Distribution

    Service entry upgrades, utility coordination, and distribution equipment, sized for your current load and designed with future capacity requirements in mind so you are not back in the field in three years.

    • Utility service application and coordination
    • Service entrance equipment and metering
    • Main distribution panels and switchgear
    • Subpanel installation and branch distribution
    • Transformer selection and installation
    • Generator paralleling and transfer equipment
    • Infrared scanning and acceptance testing
  • Branch circuit wiring and conduit installation for a commercial building

    Branch Circuits & Wiring

    Branch Circuits & Wiring

    Complete branch circuit installation for power, lighting, HVAC, specialty equipment, and low-voltage systems, all wiring methods selected for the application and long-term maintenance requirements.

    • Power receptacle and equipment circuits
    • Lighting branch circuits and dimming controls
    • HVAC and mechanical equipment wiring
    • Low-voltage and data rough-in coordination
    • Specialty process and equipment circuits
    • Grounding and bonding systems
    • Arc flash labeling and documentation
  • Emergency power system and backup generator installation for critical facilities

    Emergency Power

    Emergency Power Systems

    Generator, UPS, and automatic transfer switch design and installation for facilities where power continuity is not optional, serving government, healthcare, data, and critical infrastructure clients.

    • Emergency generator selection and installation
    • Automatic transfer switch (ATS) design and installation
    • UPS system design and installation
    • Load shedding and priority circuit design
    • Life safety and egress lighting systems
    • Fuel storage and transfer systems
    • Load bank testing and commissioning
Our Process

How we deliver phase by phase

Every project follows a rigorous, documented process, so nothing falls through the cracks between phases and nothing comes as a surprise at the end.

01
Needs Assessment & Load Analysis

We assess your facility’s existing electrical infrastructure, current and projected load requirements, utility service capacity, and any specialty system needs, including EV charging, solar interconnection, and emergency power, before a single design decision is made. This protects you from undersized systems and avoids the cost of upgrading service entry twice.

02
System Design & Engineering

Load calculations, single-line diagrams, panel schedules, conduit routing plans, and lighting design are developed and coordinated with architectural and structural drawings. All designs are reviewed for constructability before finalization, not after the conduit is already in the wrong place.

03
Permit Documents & Utility Coordination

Permit-ready construction documents are produced and submitted to the AHJ. Simultaneously, we initiate utility service applications, interconnection requests, and any required coordination with Georgia Power or the local utility, early enough that utility response timelines don’t drive construction delays.

04
Procurement & Pre-Construction

Equipment specifications, long-lead item identification, and material procurement are managed against the construction schedule. Switchgear, transformers, generators, and specialty equipment are ordered early. We do not wait until mobilization to find out something has a 20-week lead time.

05
Rough-In & Installation

Conduit, raceway, wire pulls, equipment setting, and device installation are performed to NEC standards with active quality control at each phase. Foreman sign-off is required before walls close or slabs pour. No assumption that it was done right; it gets checked.

06
Terminations, Testing & Inspection

All conductors are terminated, equipment is energized in sequence, and every circuit is tested before the inspector arrives. We schedule inspections proactively and maintain a zero-tolerance standard for failed inspections. The system is commissioned and verified against the design before the owner takes occupancy.

07
Closeout & Documentation

As-built drawings, panel schedules, equipment data sheets, warranty documentation, and inspection records are compiled and delivered at closeout, so you know exactly what you have, exactly where everything is, and exactly who to call when something needs service five years from now.

Let’s build your future together

For property owners

Start your project

From first assessment to final commissioning: one licensed team, full accountability, zero handoffs.

Get started

For developers & investors

Partner with The Black Table

Join our network of clients and partners building the next generation of clean energy infrastructure.

Contact us